Actor PLUS PVA Dropper Low Profile Version
Simple PVA dropper designed to keep your PVA bags off the standard door flaps and away from the water to keep them dry whilst being driven out in the boat.
Unfortunately the Actor PLUS standard hopper doors let a small amount of water pass through them during driving, this can melt your bag on the way to your spot and stop you delivering your PVA bag as intended.
We’ve designed this Low profile PVA dropper to be a cheap cost effective way of keeping your bags dry from the underneath.
Can be used with the standard Hopper cover when it’s raining to keep the bags dry.
The PVA Dropper consists of the following parts :
Main body, this is just drop into the hull and has been perfectly matched to the Hull design of the Actor PLUS - and as you would expect fit’s like a glove.
It also incorporates a cut-out to allow snug fitment of the body into the hull where the hopper divider would normally fit.
The body has an angled line slot to allow the Solid bag leader to pass through to the rear of the original doors.
Bombay Doors / Flaps, these have been specially designed to have a perfect rounded contact point with the original hopper doors, this minimises friction and allows the flaps to be shut as the original doors are shut - so no messing around holding the flaps out the way or having to remove the system and reset every time. The "lift" of the PVA bag is 14mm over the original doors.
Pivoting Bushes / Screws, we utilised the same technology from the Vulcan Rear mount to ensure screws could be fully tightened without “pinching” the body together - this give a nice resistance free loose design without the fear of it coming unattached. To do this we utilise plastic bushes with plastic welded inserts into the flaps.
Instructions to use :-
Open the hopper doors, insert the PVA dropper.
Load your PVA bag through the doors into the hopper
Close the doors whilst ensuring the leader is not trapped in the doors
Place the solid bag on the dropper and ensure the leader is fed through the hole in the dropper
When putting out the second rod, please ensure to dry any water from the flaps before placing a bag on it !
Manufactured from the highest quality 3D printed ASA filament - will not fade or distort in sunlight
Will be supplied already fully assembled ready to use.
Main body will be black, optional coloured flaps (only Red, Blue & Grey ASA Available currently) please make your selection when ordering.
Simple PVA dropper designed to keep your PVA bags off the standard door flaps and away from the water to keep them dry whilst being driven out in the boat.
Unfortunately the Actor PLUS standard hopper doors let a small amount of water pass through them during driving, this can melt your bag on the way to your spot and stop you delivering your PVA bag as intended.
We’ve designed this Low profile PVA dropper to be a cheap cost effective way of keeping your bags dry from the underneath.
Can be used with the standard Hopper cover when it’s raining to keep the bags dry.
The PVA Dropper consists of the following parts :
Main body, this is just drop into the hull and has been perfectly matched to the Hull design of the Actor PLUS - and as you would expect fit’s like a glove.
It also incorporates a cut-out to allow snug fitment of the body into the hull where the hopper divider would normally fit.
The body has an angled line slot to allow the Solid bag leader to pass through to the rear of the original doors.
Bombay Doors / Flaps, these have been specially designed to have a perfect rounded contact point with the original hopper doors, this minimises friction and allows the flaps to be shut as the original doors are shut - so no messing around holding the flaps out the way or having to remove the system and reset every time. The "lift" of the PVA bag is 14mm over the original doors.
Pivoting Bushes / Screws, we utilised the same technology from the Vulcan Rear mount to ensure screws could be fully tightened without “pinching” the body together - this give a nice resistance free loose design without the fear of it coming unattached. To do this we utilise plastic bushes with plastic welded inserts into the flaps.
Instructions to use :-
Open the hopper doors, insert the PVA dropper.
Load your PVA bag through the doors into the hopper
Close the doors whilst ensuring the leader is not trapped in the doors
Place the solid bag on the dropper and ensure the leader is fed through the hole in the dropper
When putting out the second rod, please ensure to dry any water from the flaps before placing a bag on it !
Manufactured from the highest quality 3D printed ASA filament - will not fade or distort in sunlight
Will be supplied already fully assembled ready to use.
Main body will be black, optional coloured flaps (only Red, Blue & Grey ASA Available currently) please make your selection when ordering.
Simple PVA dropper designed to keep your PVA bags off the standard door flaps and away from the water to keep them dry whilst being driven out in the boat.
Unfortunately the Actor PLUS standard hopper doors let a small amount of water pass through them during driving, this can melt your bag on the way to your spot and stop you delivering your PVA bag as intended.
We’ve designed this Low profile PVA dropper to be a cheap cost effective way of keeping your bags dry from the underneath.
Can be used with the standard Hopper cover when it’s raining to keep the bags dry.
The PVA Dropper consists of the following parts :
Main body, this is just drop into the hull and has been perfectly matched to the Hull design of the Actor PLUS - and as you would expect fit’s like a glove.
It also incorporates a cut-out to allow snug fitment of the body into the hull where the hopper divider would normally fit.
The body has an angled line slot to allow the Solid bag leader to pass through to the rear of the original doors.
Bombay Doors / Flaps, these have been specially designed to have a perfect rounded contact point with the original hopper doors, this minimises friction and allows the flaps to be shut as the original doors are shut - so no messing around holding the flaps out the way or having to remove the system and reset every time. The "lift" of the PVA bag is 14mm over the original doors.
Pivoting Bushes / Screws, we utilised the same technology from the Vulcan Rear mount to ensure screws could be fully tightened without “pinching” the body together - this give a nice resistance free loose design without the fear of it coming unattached. To do this we utilise plastic bushes with plastic welded inserts into the flaps.
Instructions to use :-
Open the hopper doors, insert the PVA dropper.
Load your PVA bag through the doors into the hopper
Close the doors whilst ensuring the leader is not trapped in the doors
Place the solid bag on the dropper and ensure the leader is fed through the hole in the dropper
When putting out the second rod, please ensure to dry any water from the flaps before placing a bag on it !
Manufactured from the highest quality 3D printed ASA filament - will not fade or distort in sunlight
Will be supplied already fully assembled ready to use.
Main body will be black, optional coloured flaps (only Red, Blue & Grey ASA Available currently) please make your selection when ordering.